Process Control Instruments: Process Control Products

Process Chart Recorders

Have your recorders ever run out of chart paper or ink? Perhaps, you’ve had paper jams or the mechanical drive mechanism of your recorders acts up from time to time. Maybe you had to actually look for data on some old charts and didn’t have even a little bit of fun doing it.

We have a solution. Our new PR20 is the perfect replacement for your old recorder. It’s DIN cutout fits in the hole left by most recorders with a European heritage. In minutes it can be programmed for up to six channels of RTD’s, thermocouples, Voltage or mA signals in any mixture and any range.

We also have a line of Temperature/Humidity Recorders - Thermohygrographs whenever you need a record of humidity and temperature conditions. Just put them in place and start recording, no connections, not even a power cord. That's faster, easier and likely less expensive than electronic instrumentation and data loggers.

Learn More

Digital Temperature Controllers Fuji PXR Series

The PXR series comes in several sizes - 1/32 DIN, 1/16 DIN, 1/8 DIN and 1/4 DIN. Besides the standard features including auto-tuning and fuzzy logic, they also come with self-tuning. This innovative feature automatically retunes the controller under certain conditions without the need to revert to auto-tuning.

Fuji PXR Series Digital Temperature Controllers

PXR3 1/32 DIN Fuzzy Logic Temperature Controller

PXR4 1/16 DIN Fuzzy Logic Temperature Controller

PXR5 1/8 DIN Fuzzy Logic Temperature Controller

PXR9 1/4 DIN Fuzzy Logic Temperature Controller

 

DCS 4000 Waterless Tobacco Curing Controller

The DCS-4000 tobacco curing system controller is a state of the art control system that gives you the precise control needed to cure a quality leaf.

The digital display on the DCS-4000 includes time controlled temperature and humidity indicators as well as an automatic advance rate capability.

The DCS-4000 tobacco curing system controllers can be upgraded to allow communication with your iPad or PC. Once the available hardware and software are added, you can monitor and control kilns remotely from the comfort of your home or anywhere the internet is available.

For the last 30 years Enercorp has built temperature controllers, sensors and indicators used in tobacco kilns worldwide.

Learn More

Programmable Temperature Relay ETTR

The ETTR is a programmable temperature relay with the ability to act as an ON/OFF temperature controller. The device is capable of fully stand alone operation, but may be monitored and programmed with the custom software and a serial RS232 interface. The unit may be programmed in two control modes: (a) temperature range mode in which it will turn ON the output relay between two defined temperatures and (b) set point mode in which it will turn ON below a defined temperature and OFF above a defined temperature. The span between the temperatures may be adjusted to customize the hysteresis. The ETTR may also be placed in a manual mode of operation in which the relay is controlled via the GUI software.

Learn More

Pallet Sterilization Controllers

The EIL3000P Pallet Sterilizers and Pallet Sanitizers automatically control the complete sterilization process. The well thought out display makes it easy for the operator to know the operating conditions at all times.

Learn More

Drying, Cooking and Curing Controllers

The EIL3000 controls the temperature and humidity during a batch drying, curing or cooking process. The well thought out display makes it easy for the operator to know the operating conditions at all times.

The three displays and seven led indicators let the operator see at a glance the operating conditions. Changing setpoints is as easy as holding down the button to the right of the displayed variable while pressing the up or down arrow keys.

The operator can set the start and stop temperatures as well as the ramp rate in degrees / hour by pressing one button and the up or down arrows. The elapsed time of the process displayed by pressing the hours button.

It can be programmed as either a ramp and soak or delta T controller.

Learn More

2-Wire Economy Hockey Puck Transmitters

Temperature Transmitter, "Hockey Puck" style fits directly in the head of an RTD temperature sensor offering several advantages over a plain sensor.

Temperature Transmitter wiring is simplified since the lead resistance of the wires connecting the sensor to the control system can normally be ignored. Installation and start-up is simple and the signal can travel over long transmission lines without interference.

Temperature Transmitter 2-Wire Economy RTD Hockey Puck is programmable it can be re-ranged from your PC's desktop.

Now get the accuracy and flexibility of a programmable Temperature Transmitter at analog transmitter prices.

Learn More

Isolated Programmable Temperature Transmitter Hockey Puck Style

Isolated programmable temperature transmitter is the one you need to stock for all your maintenance needs.

Isolated Programmable temperature transmitter can be programmed using your PC and the available software for any one of 7 RTD or 13 thermocouple types or customize the calibration to fit none standard transmitter outputs. The output signal can be inverted and can be programmed to be linear with temperature or linear with resistance or mV input.

Isolated Programmable temperature transmitterfeatures include a 7mm central hole for easy spring loading of 1/4" tube, insulating barriers between terminals to prevent shorts and a captive cover on programming pins to keep them clean.

Learn More

Stainless Steel Pressure Transmitter

Stainless Steel Pressure Transmitters Model PX61 features compact construction, an integral amplifier, 2-wire 4-20mA output signal and extensive medium compatablility. Stainless Steel Pressure Transmitters Model PX61 design provides a 1/2% accurate, low cost pressure transmitter that can operate over a wide temperature range with corrosion resistance.

Learn More

Digital Indicator

The DIS-3000 digital indicator is a low cost, instrument for displaying one or two temperatures from RTD sensors.
The standard version accepts two RTD temperature sensor inputs. The first value is continually displayed and the second is displayed when a button on the front of the instrument is depressed.

Wet/Dry bulb: The DIS-3000 is a convenient way to monitor temperatures from a wet and dry bulb psychrometer. Heat pumps: The DIS-3000 is an easily installed and inexpensive way to monitor supply and return temperatures from any cooling or heating equipment. Since it can be powered by a 9 volt battery it can even be used as a portable instrument in a pinch.

The thermostat style surface mount case is quick to install with sheet metal screws and does not require a panel cut-out. You will need a knock out behind the case for the power and temperature sensor connections.

Learn More


ENERCORP INSTRUMENTS LIMITED

About Enercorp

Enercorp Instruments Ltd is a Manufacturer of Temperature, Pressure & Humidity Instrumentation. Used for Industrial, Food Processing, Climate Monitoring & Energy Management Applications.

Sitemap

Enercorp Products

Our products include temperature, pressure, humidity & climate instruments for sensing, controlling, recording and indicating; as well as wind speed & direction systems, RTD elements, smokehouse probes & custom built RTD, thermocouple and thermistor temperature sensors, temperature transmitters/transducers, thermowells, moisture meters, signal conditioners, power supplies, air quality & gas monitors..

Contact Enercorp

  • Toll Free:
    1-800-363-2677
  • Telephone:
    416-231-5335
  • Fax:
    416-231-7662
  • Email and Website:
    sales@enercorp.com www.enercorp.com
  • Head Office:
    25 Shorncliffe Road,
    Toronto, ON
    M9B 3S4 Canada